MG Chemicals Static Mixing Tip for 50 mL Dual Epoxy Cartridge Pack of 5

#ad
MG Chemicals 8MT-50 #ad - For use with: 832hd-50ml, 8329tff-50ml, 8329tfm-50ml and 8329tfS-50ML Dual Epoxy Cartridges. It is designed to dispense an even and accurate amount of compound eliminating spoilage. Provides homogeneous mixture of low to medium viscosity 2-part systems. Simply attach the tip to dual cartridge end and twist to lock.

The 8mt mixing tips are single use static mixer for 2-part low to medium viscosity cartridge systems. Allow precise application directly where you need it. The mixer works using stationary elements inside a narrow cylindrical tube. The 8mt-50 mixing tip unit features a standard flow tip while the 8MT-50FT has a fine tip for greater precision dispensing.

To reuse a partially filled cartridge with the single use static mixer, simply remove the nut and plug preserving the remaining epoxy in the cartridge, and affix a new mixing tip to the end. To reuse a partially filled cartridge, simply remove the cap preserving the remaining epoxy in the cartridge, and affix a new mixing tip to the end.

MG Chemicals Static Mixing Tip for 50 mL Dual Epoxy Cartridge Pack of 5 #ad - This forces the materials to combine as it travels through the length of the mixer and provides a homogenous mix of hardener and resin that can be applied directly onto the targeted area. Simply remove the cartridge nut and plug, attach the static mixer to the tip, and re-screw on the nut to hold the mixer in place.

#ad



MG Chemicals 832HD Black 1:1 Epoxy Encapsulating and Potting Compound, 45 milliliters Dual Pneumatic Dispenser

#ad
MG Chemicals 832HD-50ML #ad - In its cured state, static discharges, shocks, it protects electronic assemblies against corrosion, vibrations, and mechanical impacts. Applications & usages the 832HD epoxy is used to pot or encapsulate printed circuit assemblies in a protective block. Further, harsh chemicals, it is extremely resistant harsh environments with salt water, and high humidity.

Additional static mixers 8mt-25 or 8mt-50 for 832hd-25ml and 832HD-50ML sold separately. Full cure @80 °c 176 °F = 1 hour. The 832hd 1: 1 epoxy potting and encapsulating compound is a two-part, economical, chemical, flow able, electronic-grade epoxy that provides excellent physical, and electrical protection.

MG Chemicals 832HD Black 1:1 Epoxy Encapsulating and Potting Compound, 45 milliliters Dual Pneumatic Dispenser #ad - Non-corrosive. Very high tensile and compressive strength. Dispensing gun 8dg-50-1-1 for 832HD-50ML sold separately. The cured epoxy improves reliability, operational range, and lengthens the life of electrical and electronic parts. Flow able and high durability. It is very easy to use due its 1: 1 mix ratio and because it is room temperature curable.

Protects electronics from moisture, fungus, humidity, corrosion, and static discharges. Full cure @22 °c 72 °F = 24 hours.

#ad



MG Chemicals 9200 Structural Epoxy Adhesive 45 milliliters Dual Pneumatic Dispenser

#ad
MG Chemicals 9200-50ML #ad - It has an excellent chemical resistance to moisture, antifreeze, automotive fluids, gasoline, salt water, hydraulic fluids, detergents, acids, and bases. The 9200 is electrically insulating and chemically resistant, which helps prevent corrosion damage. Easy mix ratio 1A: 1B by volume. Very high tensile and compressive strength.

It is especially suitable for sheet molding compound SMC and glass-reinforced plastics GRP bonding. Bonds dissimilar materials. It offers excellent adhesion to a wide range of difficult to bond to materials, engineered thermoplastics, metals, ceramics, including glass, and thermoset laminates such as SMC sheet molding compound and GRP glass-reinforced plastics.

MG Chemicals 9200 Structural Epoxy Adhesive 45 milliliters Dual Pneumatic Dispenser #ad - It is also excellent for potting electronics, especially when the enclosure has holes or seams where a no thixotropic potting compound would flow through. Toughened, smooth, thixotropic paste. Very strong adhesion. Applications & usages: this adhesive is primarily used for creating long lasting load bearing joints, especially in situations where vibration resistance is key or where dissimilar materials are being joined.

In addition, dissimilar metals can be bonded together without fear of causing galvanic corrosion because the adhesive prevents current flow through the bond. The toughened adhesive protects against vibration damage when fully cured, but remains sufficiently flexible to accommodate thermal cycling stresses when bonding materials with different coefficients of thermal expansion.

#ad



Dispenser Gun, 50ml Dispensing Gun Kit Impression Mixing Dispensing Dispenser AB Gun 1:1/1:2

#ad
Yarr Store #ad - Working life: 30 minutes, cure time: 24 hours. Full cure @80 °c 176 °F = 1 hour. 1. Toughened, smooth, thixotropic paste. Fitting mixing gun, size:19 x 18 x 6cm/ 7. 48" x 7. 09" x 2. 36", tube cartridges capacity: 50ml. Bonds dissimilar materials. Used for smearing or dripping various two-component adhesives or coatings to solve the problem of uneven mixing of two-component adhesive products.

Specifications: material: plastic, metal suitable: 50ml Ratio: 1:1/ 1:2 Size: 19 x 18 x 6cm/7. 48" x 7. 09" x 2. 36" weight: 210g package include: 1 x Impression Mixing Dispensing Dispenser Gun Non-corrosive. Very suitable for standard manual operation, user-friendly design, demolition and use are very simple.

Dispenser Gun, 50ml Dispensing Gun Kit Impression Mixing Dispensing Dispenser AB Gun 1:1/1:2 #ad - Very high tensile and compressive strength. Gap Filler. Mixing and delivery of impression materials made easy with this handgun cartridge dispenser. 1: 1 mix ratio. It's suit for 50ml kits, works with Loctite, Devcon, Gorilla, araldite, and others with standard 50ml cartridges. Don't be distracted by the plunger diameters as this tool also works on similar material kits with 2:1 and 1:1 ratios.

#ad



MG Chemicals 8329TFM Thermally Conductive Adhesive, Medium Cure, 45 milliliters Dual Pneumatic Dispenser

#ad
MG Chemicals 8329TFM-50ML #ad - It is suitable for use in manufacturing operations including automatic dispensing applications. Dispensing gun cat# 8dg-50-1-1 and static mixers cat# 8MT-50, 8MT-50FT sold separately. Full cure @80 °c 176 °F = 1 hour. It's suit for 50ml kits, works with Loctite, Devcon, Gorilla, araldite, and others with standard 50ml cartridges.

Don't be distracted by the plunger diameters as this tool also works on similar material kits with 2:1 and 1:1 ratios. It is filled with thermally conductive ceramic powders for excellent thermal conductivity. Easy mix ratio 1A: 1B by volume. Working life of 45 minutes. 1: 1 mix ratio. Toughened, smooth, thixotropic paste.

MG Chemicals 8329TFM Thermally Conductive Adhesive, Medium Cure, 45 milliliters Dual Pneumatic Dispenser #ad - It bonds well to metals, glass, ceramics, and most plastics used in electronic assemblies. Fitting mixing gun, size:19 x 18 x 6cm/ 7. 48" x 7. 09" x 2. 36", tube cartridges capacity: 50ml. 1 w/m k. Used for smearing or dripping various two-component adhesives or coatings to solve the problem of uneven mixing of two-component adhesive products.

#ad



Fast Cure Epoxy, 25 mL Dual Dispenser - MG Chemicals 8329TFF Thermally Conductive Adhesive

#ad
MG Chemicals 8329TFF-25ML #ad - Flow able and high durability. 6. Cure time of 150 minutes at 65 °C or 24 hours at room temperature. 2. Full cure @80 °c 176 °F = 1 hour. It is also flame retardant, and meets the UL 94V-0 standard. 1: 1 mix ratio. 1. It is suitable for use with dual-syringes, mix-tips and automatic dispensing systems. Very strong adhesion.

Do not discard cap. Working life: 4 minutes, set time: 15 minutes. Used for smearing or dripping various two-component adhesives or coatings to solve the problem of uneven mixing of two-component adhesive products. Thermal conductivity: 1. Twist and remove the cap from the cartridge or syringe. Bonds dissimilar materials.

Fast Cure Epoxy, 25 mL Dual Dispenser - MG Chemicals 8329TFF Thermally Conductive Adhesive #ad - Thermal conductivity of 0 Heat cure: put in oven at 65 °C 149 °F for 15 min. Heat cure to achieve optimal conductivity. Dispense and discard 3 to 5 ml of the product to ensure a homogeneous mixture. Application instructions: for best results, follow the procedure below. It's suit for 50ml kits, devcon, araldite, Gorilla, works with Loctite, and others with standard 50ml cartridges.

#ad



CNBTR 50ml Dispenser Gun Impression Mixing Dispensing Gun Applied to 50ml 1: 1/1: 2 AB Plastic Tube

#ad
#ad - Cure time: 3 hours at room temperature or 15 minutes at 65 °c 149 °f. Very strong adhesion. Cure time of 150 minutes at 65 °C or 24 hours at room temperature. Toughened, smooth, thixotropic paste. Easy mix ratio 1A: 1B by volume. Automatic mixing and delivery of impression materials made easy with this handgun cartridge dispenser.

Gap Filler. Package include: 1 x Impression Mixing Dispensing Dispenser Gun Non-corrosive. Full cure @80 °c 176 °F = 1 hour. Thermal conductivity of 0 Fitting mixing gun, size:19 x 18 x 6cm/ 7. 48" x 7. 09" x 2. 36", tube cartridges capacity: 50ml. It's suit for 50ml kits, araldite, works with Loctite, Gorilla, Devcon, and others with standard 50ml cartridges.

CNBTR 50ml Dispenser Gun Impression Mixing Dispensing Gun Applied to 50ml 1: 1/1: 2 AB Plastic Tube #ad - Don't be distracted by the plunger diameters as this tool also works on similar material kits with 2:1 and 1:1 ratios. Flow able and high durability. Function: Dispensing temporary crown & bridge materials. Not work with dp420 37ml cartridges or likely any 37ml nozzlesSpecification: Material: Plastic, Metal Color: Gray and Black Suitable Cartridge: 50ml Dimension:19 x 18 x 6cm/7.

#ad



HY 4090 Hybrid Adhesive, 50 g Cartridge

#ad
Loctite 2123350 #ad - Fixture time is 90 - 180 secs. Flow able and high durability. Good moisture, chemical, temperature up to 150°C and impact resistance-the bond will endure. Bonds dissimilar materials. Very strong adhesion. Working life of 45 minutes. Working life: 4 minutes, set time: 15 minutes. Suitable for a variety of substrates, including metals, most plastics and rubbers-opening up your design possibilities.

Easy mix ratio 1A: 1B by volume. Working life: 30 minutes, cure time: 24 hours. 8 w/m·K. This ca epoxy is Henkel's instant adhesive suitable for structural applications. 1: 1 mix ratio. Thermal conductivity of 0 Automatic mixing and delivery of impression materials made easy with this handgun cartridge dispenser.

HY 4090 Hybrid Adhesive, 50 g Cartridge #ad - Loctite hy 4090 has a high viscosity and is an off-white to light yellow gel. Cure time: 3 hours at room temperature or 15 minutes at 65 °c 149 °f. Gap Filler. Don't be distracted by the plunger diameters as this tool also works on similar material kits with 2:1 and 1:1 ratios. Gorilla, works with loctite, Devcon, Araldite, and others with standard 50ml cartridges.

#ad



3M Scotch-Weld Epoxy Adhesive DP100 Plus Clear, 1.69 oz Pack of 1

#ad
3M 021200871955 #ad - Easy mix ratio 1A: 1B by volume. Cure time of 150 minutes at 65 °C or 24 hours at room temperature. Very strong adhesion. Provides handling strength in approximately 15 minutes at room temperature. Fitting mixing gun, size:19 x 18 x 6cm/ 7. 48" x 7. 09" x 2. 36", tube cartridges capacity: 50ml. It's suit for 50ml kits, araldite, Devcon, works with Loctite, Gorilla, and others with standard 50ml cartridges.

Don't be distracted by the plunger diameters as this tool also works on similar material kits with 2:1 and 1:1 ratios. Full cure @80 °c 176 °F = 1 hour. Working life: 30 minutes, cure time: 24 hours. Meters and mixes as it dispenses, maximizing adhesive work-time. Provides high shear and peel strength. Protects electronics from moisture, fungus, corrosion, humidity, and static discharges.

3M Scotch-Weld Epoxy Adhesive DP100 Plus Clear, 1.69 oz Pack of 1 #ad - Full cure @22 °c 72 °F = 24 hours. Hy 4090 is iso 10993 compliant-suitable for the assembly of disposable medical devices. Effective system for bonding, joining, encapsulating, assembling, potting, gluing, attaching, and sealing applications. Very flexible adhesive formula provides strong, permanent bond even under vibration and impact.

#ad



MG Chemicals 419D Premium Acrylic Conformal Coating, 55 mL Bottle, IPC 830, UL 94V-0 File # E203094

#ad
MG Chemicals 419D-55ML #ad - It is ideal for high moisture environments and applications requiring easy repair and rework. Non-corrosive. Automatic mixing and delivery of impression materials made easy with this handgun cartridge dispenser. Clear formula provides a clean bond line. Cure time: 3 hours at room temperature or 15 minutes at 65 °c 149 °f.

8 w/m·K. Easy mix ratio 1A: 1B by volume. Flexible when cured, making it a good choice for bonding dissimilar surfaces. Meters and mixes as it dispenses, maximizing adhesive work-time. Flame retardant-meets ulu 94v-0 standard. Bonds dissimilar materials. 1 w/m k. Good moisture, chemical, temperature up to 150°C and impact resistance-the bond will endure.

MG Chemicals 419D Premium Acrylic Conformal Coating, 55 mL Bottle, IPC 830, UL 94V-0 File # E203094 #ad - Cure time of 150 minutes at 65 °C or 24 hours at room temperature. Ideal for light volume dispensing. Hy 4090 is iso 10993 compliant-suitable for the assembly of disposable medical devices. Specially used for smearing or dripping various two-component adhesives or coatings to solve the problem of uneven mixing of two-component adhesive products.

Size:fitting mixing gun. Applicable rate: 【1:1 ratio and 1:2 ratio adhesive】 Fitting Capacity of Tube Cartridges : 【50ml Cartridges ONLY】.

#ad



3M Scotch-Weld 08966 Epoxy Adhesive DP420 50mL, DP420, Black

#ad
3M 08966 #ad - Very strong adhesion. Good moisture, chemical, temperature up to 150°C and impact resistance-the bond will endure. Specially used for smearing or dripping various two-component adhesives or coatings to solve the problem of uneven mixing of two-component adhesive products. Size:fitting mixing gun. Applicable rate: 【1:1 ratio and 1:2 ratio adhesive】 Fitting Capacity of Tube Cartridges : 【50ml Cartridges ONLY】.

Hy 4090 is iso 10993 compliant-suitable for the assembly of disposable medical devices. Full cure @80 °c 176 °F = 1 hour. Fitting mixing gun, size:19 x 18 x 6cm/ 7. 48" x 7. 09" x 2. 36", tube cartridges capacity: 50ml. 1: 1 mix ratio. Cure time of 150 minutes at 65 °C or 24 hours at room temperature. Provides high sheer and peel strength for reliable bonding.

3M Scotch-Weld 08966 Epoxy Adhesive DP420 50mL, DP420, Black #ad - Provides handling strength in approximately 15 minutes at room temperature. Cure time: 3 hours at room temperature or 15 minutes at 65 °c 149 °f. 1: 1 mix ratio. Toughened, smooth, thixotropic paste.

#ad